Street Light fittings (Top open type) in die-cast aluminum suitable for HPSV/MH tubular lamp with toughened glass and complete with control gear with heavy duty copper ballast, Ignitor and capacitor, but without lamp suitable for 230/240 Volts, 50 Hz AC supply.

Street Light fittings (Full Glass Type) Single Piece in die-cast aluminum suitable for HPSV/MH tubular lamp with full toughened glass and complete with control gear with heavy duty copper ballast, Ignitor and capacitor, but without lamp suitable for 230/240 Volts, 50 Hz AC supply.

Street Light fittings (Full Glass Type) Single Piece in die-cast aluminum suitable for HPSV/MH tubular lamp with full toughened glass and complete with control gear with heavy duty copper ballast, Ignitor and capacitor, but without lamp suitable for 230/240 Volts, 50 Hz AC supply.

HPSV Street Light Luminaire deep drawn with Acrylic Cover and IP53 Protection confirming to IS: 10322 complete with Ballast, Capacitor, Ignitor but without lamp suitable for 230/240 Volts, 50 Hz AC supply.

Energy Saving HPSV Street Light Fitting of high intensity, dust, moisture and vermin proof with IP-65 Protection suitable for 230V/240V confirming to IS : 10322 (Part5/Sec 3) and IS: 13383 (Part 2)/1992. The lamp confirming to IS: 9971 (Part 1 & 2)-1981 (Reaffirmed 2202) complete with 230V, 150W HPSV Lamp with its control gear and connectors duly wired   Construction –

1. Highly polished, mirror finish stainless steel reflector-cum-body
2. Toughened glass cover with neoprene rubber gasket duly impregnated with insecticide and water repellant chemical on the periphery of lamp compartment.
3. Die-cast aluminum suitable for HPSV/MH tubular lamp with toughened glass and complete with control gear with heavy duty copper ballast, Ignitor, fuse and capacitor
4. Lamp holder base screw type E-40 skirted porcelain
5. Powder coated metallic cover provided for the control gear compartment with hinging arrangement.
6. Provision for mounting on a 50 mm OD pipe with suitable galvanized clamps & nuts.

Energy efficient tube light streetlight fitting made out of CRCA / Aluminum sheet duly phosphate and powder coated with heavy duty electronic choke suitable for FTL lamps for operation on 230Volt AC supply 50 Hz confirming to IS: 10322/Part 5/Sec 3/1987. The ballast used in the fitting confirms to IS: 13021/Part 1 & 2/1991.
Construction -

1. CRCA / aluminum sheet housing duly phosphate and powder coated
2. Good quality clear ribbed acrylic cover
3. Rubber gasket is provided to ensure prevention of dust/water seepage into fitting
4. Side entry type suitable for pipe upto OD 38mm
5. Internal wiring is done with PVC covered of copper wire
6. Earthing terminal is provided near connector terminals

  Accessories-
Fittings comes with

1. Electronic ballast confirming to IS: 13021/Part 1 & 2/1991 suitable for 230 volt
2. Bipin lamp holder confirming to relevant IS

  Application -
Street Lighting

Energy efficient tube light streetlight fitting made out of CRCA sheet of 18 Gauge duly phosphate and powder coated with heavy duty electronic choke suitable for FTL lamps for operation on 230Volt AC supply 50 Hz confirming to IS: 10322/Part 5/Sec 3/1987. The ballast used in the fitting confirms to IS: 13021/Part 1 & 2/1991.
Construction -

1. CRCA sheet housing made out of 18 Gauge duly phosphate and powder coated
2. Good quality clear acrylic cover of 2mm thickness.
3. EPDM/Neoprene rubber gasket is provided to ensure prevention of dust/water seepage into fitting (IP-54).
4. Side entry type suitable for pipe upto OD 38mm
5. Internal wiring is done with multi-stranded PVC covered of copper wire of 0.5 sqmm.
6. Earthing terminal is provided near connector terminals

Accessories-
Fittings comes with

1. Electronic ballast confirming to IS: 13021/Part 1 & 2/1991 suitable for 230 volt
2. Bipin lamp holder confirming to relevant IS

Application -
Street Lighting

Energy efficient Mine Roadway Light Fitting made our of CRCA sheet duly phosphate and powder coated with heavy duty copper choke suitable for FTL lamps, 110/125 Volt AC supply 50 Hz confirming to IS: 10322/Part 1 to 5.
Construction -

1. CRCA sheet housing duly phosphate and powder coated
2. Guard of GI wire of 3 mm size is provided for the protection of good quality clear acrylic cover.
3. EPDM/Neoprene rubber gasket is provided to ensure prevention of dust/water seepage into fitting.
4. All screws provided with the fitting are passivated for preventing corrosion
5. Clamping arrangement is provided for horizontal mounting of the fitting
6. Provision for cable entry from one side with a cable gland of suitable size.
7. Internal wiring is done with multi-stranded PVC covered copper wire.
8. Earthing terminal is provided near connector terminals

Accessories-
Fittings comes with

1. Copper wound 20watt ballast confirming to IS: 1534 suitable for 110/125 volt
2. Bipin lamp holder confirming to relevant IS
3. Starter Holder confirming to relevant IS
4. Starter confirming to relevant IS
5. Tube 20watt 2 feet confirming to relevant IS

Application -
Mines

Energy efficient tube light fitting made out of CRCA sheet of 18 Gauge duly phosphate and powder coated with heavy duty electronic choke suitable for FTL lamps for operation on 110Volt AC supply 50 Hz confirming to IS: 10322. The ballast used in the fitting confirms to IS: 13021/Part 1 & 2/1991.
Construction -

1. CRCA sheet housing made out of 18 Gauge duly phosphate and powder coated
2. Guard of GI wire of 3 mm size is provided for the protection of good quality clear acrylic cover of 2mm thickness.
3. EPDM/Neoprene rubber gasket is provided to ensure prevention of dust/water seepage into fitting (IP-54).
4. All screws provided with the fitting are passivated for preventing corrosion
5. Clamping arrangement is provided for horizontal mounting of the fitting
6. Provision for cable entry from one side with a cable gland of suitable size.
7. Internal wiring is done with multi-stranded PVC covered of copper wire of 0.5 sqmm.
8. Earthing terminal is provided near connector terminals

  Accessories-
Fittings comes with

1. Electronic ballast confirming to IS: 13021/Part 1 & 2/1991 suitable for 110 volt
2. Bipin lamp holder confirming to relevant IS

  Application -
Mines

	Note: The actual product may differ from the picture given above